
XINCHI SMR E5 Shaft Mounted Speed Reducer | 5:1 SMSR Gearbox
XINCHI SMR E5 5:1 SMSR gearbox: exact ratio 5.047:1, 55/65 mm output bore, 28 mm input shaft and 41 kg catalog weight. View conveyor applications, speed-dependent kW ratings and shaft-fit selection details.
SMR E5 5:1 SMSR gearbox for conveyor drives
The XINCHI SMR E5 shaft mounted speed reducer uses a hollow output hub and a torque arm for a compact belt-driven arrangement. This model has a nominal 5:1 reduction; its exact catalog ratio is 5.047:1. Buyers searching for an SMR reducer, SMSR gearbox or conveyor gearbox can use the model-specific data below to compare the correct frame.
E5 specifications
| Parameter | SMR E5 |
|---|---|
| Nominal reduction ratio | 5:1 |
| Exact reduction ratio | 5.047:1 |
| Standard / alternative output bore | 55 / 65 mm |
| Input shaft diameter | 28 mm |
| Catalog weight, 5:1 unit | 41 kg |
| Catalog output torque at 100 rpm | 983 Nm |
| Backstop | Not recommended for 5:1 units |
Power ratings at selected output speeds
Ratings below are catalog power ratings in kW at the stated output speed. They are not a universal motor-power range. Apply the service factor and check the complete drive before selection; the torque above applies specifically at 100 rpm.
| Output speed (rpm) | Power rating (kW) |
|---|---|
| 100 | 10.29 |
| 150 | 13.13 |
| 200 | 14.91 |
| 250 | 16.80 |
| 300 | 19.43 |
| 350 | 21.84 |
| 400 | 23.57 |
Application: Screen-feed and stone-crusher plant conveyors
E5 is a candidate for a screen-feed belt or a stone-crusher plant conveyor after the actual loading pattern has been checked. Feed surges at a hopper and starts with aggregate on the belt may require a higher service factor than a uniformly loaded transfer line. Assess the reducer separately from the crusher drive: this page describes the conveyor gearbox, not a direct crusher replacement. Check the 55 mm standard or 65 mm alternative output bore and allow service access around the torque arm.

Selection for India-market SMSR gearbox inquiries
For an SMSR gearbox or belt conveyor gearbox inquiry from India, specify SMR E5, the required bore, absorbed power, output rpm, motor rpm, pulley sizes, daily operating hours and load shocks. Design power equals absorbed power multiplied by the appropriate service factor; use motor power when absorbed power is unknown. Output speed equals reducer input speed divided by 5.047, and any belt-stage reduction must be included.
For example, a reducer input of 1,000 rpm gives approximately 198.1 rpm output. A pulley drive can change this input speed. A stone crusher plant conveyor, sand conveyor or grain conveyor must still be checked for its own starting and running duty. For rollback-sensitive systems, request an engineered solution: backstops are not recommended for the 5:1 units.
Construction, installation and maintenance
The series uses a cast-iron housing, alloy helical gearing, hardened shafts and double-lip oil seals. Fit the reducer close to the driven bearing and keep the input pulley close to the reducer to limit overhung loading. Secure the torque arm to a suitable rigid anchor, check alignment and guard the rotating transmission. The catalog states units are supplied without oil: fill with the specified oil grade to the correct level for the mounting orientation before operation. Confirm shaft tolerances, keys and the final drawing with XINCHI.
The main product photograph represents the SMR series; confirm the supplied E5 configuration and bore with the approved drawing.
Compare SMR models and request a quotation
Browse the SMR shaft mounted speed reducer category and the SMR series overview. Compare adjacent frames using their own ratings: SMR B5 | SMR C5 | SMR D5 | SMR F5 | SMR G5 | SMR H5 | SMR J5.
Contact XINCHI for a E5 quotation and duty check. Include your application, bore, speed, motor power, mounting orientation and delivery destination so the configuration can be confirmed.
Technical basis: SMR catalog, 5:1 ratings and dimension tables. All ratings are conditional on the specified speed and duty; final selection requires application review.